Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions
Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions
Blog Article
Every person maintains their personal thinking with regards to How to Install a Bathtub Yourself.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough project. If the old bathtub is easily accessible, the job can move immediately; if you have to open up a wall to remove the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the task and also are comfortable trying it. Instead of working with a professional to take control of a halfway-completed project, it is far better to consider using one before you begin. Opportunities are you may require a professional plumber to make tube links.
This article will certainly aid you set up a brand-new bathtub in your shower room if you have actually already acquired a new tub and also don't require to transform the arrangement of your previous water system pipes.
Your tools and also material checklist must comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted gain access to that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipelines have actually been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place between the tap and the sink. Secure the tap in position with the supplier supplied backnut. When the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Tub
Utilizing the two wood boards under its feet, position the tub in the required placement. The wood boards are valuable in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest adaptable tap connector to the ideal supply pipe by making a compression sign up with; after that do the same for the various other tap.
Switch on the water system and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bath tub as well as also inspect the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub must wait until the tub has been utilized at least when as this will settle it right into its final placement.
Preparing for the Installment
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, causing the water to penetrate the wall between the bath and the tiling, resulting in problems with moisture as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealer can split relatively early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that report on How to Install a Bathtub through a good friend on a different web blog. Are you aware of somebody who is serious about the niche? Take a moment to share it. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Schedule Now!
Report this page